- 518 - ARGP10D thru argp10m fast soft-recovery controlled avalanche rectifiers voltage range 200 to 1000 volts features high temperature metallurgically bonded constructed plastic material used carries underwriters laboratory classification 94v-0 glass passivated cavity-free junction high maximum operating temperature low leakage current excellent stability guaranteed avalanche energy absorption capab ility high temperature soldering guaranteed: 350 o c / 10 seconds, 0.375?(9.5mm) lead length, 5 lbs., (2.3kg) tension. mechanical data case: jedec do-41 molded plastic over glass body lead: plated axial leads, solderable per mil-std-750, method 2026 polarity: color band denotes cathode end mounting position: any weight: 0.012 ounce, 0.3 gram do-41 dimensions in inches and (millimeters) maximum ratings and electrical characteristics rating at 25 ambient temperature unless otherwise specified. type num ber symbol argp 10d argp 10g argp 10j argp 10k argp 10m units maximum recurrent peak reverse voltage v rrm 200 400 600 800 1000 v maximum rms voltage v rms 140 280 420 560 700 v maximum dc blocking voltage v r 200 400 600 800 1000 v min. reverse avalanche breakdown voltage @ ir=0.1ma v (br)r 300 500 700 900 1100 v maximum average forward rectified current .375? (9.5mm) lead length @ t tp = 55 i f(av) 1.3 a peak forward surge current @ t= 8.3 ms single half sine-wave superimposed on rated load (jedec method ) @ t=10ms half sine wave, tj=tjmax prior to surge, vr=v rrm max i fsm 30 20 a a non-repetitive peak reverse avalanche ener g y l=120mh tj=125 max prior to surge, inductive load switched off e rsm 10 7 mj maximum instantaneous forward voltage @ if= 1.0a @ if=1a, tj=tj max. v f 1.3 1.1 v v maximum dc reverse current @ t j =25 at rated dc blocking voltage @ t j =165 i r 1.0 100.0 ua ua maximum reverse recovery time ( note 1 ) t j =25 trr 250 300 ns typical junction capacitance ( note 2 ) cj 15.0 pf typical thermal resistance (note 3) r ja r tp 120 55 o c /w operating temperature range t j t j -65 to + 175 o c storage temperature range t stg t stg -65 to + 175 o c notes: 1. reverse recovery test conditions: i f =0.5a, i r =1.0a recover to 0.25a. 2. measured at 1.0 mhz and applied reverse voltage of 4.0 volts. 3. mount on cu-pad size 5mm x 5mm on p.c.b.
- 519 - fig.1- reverse recovery time characteristic and test circuit diagram 50 noninductive non inductive oscilloscope (note 1) pulse generator (note 2) dut (+) 50vdc (approx) (-) notes: 1. rise time=7ns max. input impedance= 1 megohm 22pf 2. rise time=10ns max. sourse impedance= 50 ohms (-) (+) 10 noninductive -1.0a -0.25a 0 +0.5a trr 1cm set time base for 5/ 10ns/ cm ratings and characteristic curves (ARGP10D thru argp10m) fig.3- maximum non-repetitive peak forward surge current peak for ward surge current . (a) 1 10 100 30 10 0 20 number of cycles at 60hz tj=tj max. 8.3ms single half sine wave jedec method fig.4- typical junction capacitance junction cap acitance.(pf) 1 10 100 10 0 100 reverse voltage. (v) tj=25 c 0 fig.5- typical instantaneous forward characteristics instantaneous for ward current . (a) 0.4 0.6 0.8 1.0 1.2 1.4 1.6 0.01 1 10 0.1 forward voltage. (v) tj=25 c pulse width-300 s 1% duty cycle 0 fig.2- maximum forward current derating curve average for ward current . (a) 25 50 75 125 175 150 100 0 0.25 0.75 1.0 0.5 tie point temperature. ( c) o 0.375" (9.5mm) lead length fig.6- typical reverse characteristics instantaneous reverse current , microamperes 0 20 40 60 80 100 120 140 10 20 1 0.1 0.01 percent of rated peak reverse voltage. (%) tj=125 c 0 tj=75 c 0 tj=25 c 0 1.25 1.5 resistive or inductive load
|
